Pipe Repair in Fulton, TX — Located Precisely, Fixed Permanently
Pipe failures range from a slow pinhole leak weeping inside a wall to a full main line rupture. Locating the failure precisely — before opening drywall or digging — is the skill that separates a clean, affordable repair from an expensive and destructive guessing operation. Masters Plumbing Service's pipe technicians in Fulton, TX use acoustic listening devices and thermal imaging cameras to find the leak first, then open only what needs to be opened.
How Masters Plumbing Service Approaches Pipe Repair in Fulton
Our techs work on every pipe material found in Fulton, TX homes, from pre-1970s galvanized to modern PEX-A crosslinked systems. The repair method matches the pipe.
🔊
Acoustic Leak Detection
Acoustic detection is most effective on pressurized supply lines. Combined with a pressure test to confirm water loss before we start, it tells us both that there's a leak and exactly where it is.
🌡️
Thermal Camera Scanning
Active water leaks create temperature differentials on wall and floor surfaces detectable with an infrared camera. A slow leak inside a wall shows as a cold, spreading zone; a hot water line leak shows the inverse. Thermal imaging confirms leak presence and approximate location before any cutting begins.
🛠️
All Pipe Materials & Joining Methods
Press-fit copper connections — particularly useful for repairs in occupied spaces where open flame is a concern — are available as an alternative to torch sweating where code permits.
🔒
Pressure-Tested Before We Leave
Drain line repairs are water-tested by running fixtures through the repaired section and visually confirming no seepage at the repair joint and downstream.
Our Pipe Repair Services
Pipe Repair Solutions for Fulton Homes
From a pinhole copper leak behind a kitchen cabinet to a full galvanized repiping, our pipe crew in Fulton, TX handles the full range.
Copper
Copper Pipe Repair & Repipe
Pitting corrosion in copper is sometimes systemic rather than localized — a single pinhole is often the first of several to appear. When the camera or pressure test finds multiple deteriorated sections, we give you an honest assessment of whether targeted repair or full copper repipe is the better long-term answer.
Galvanized
Galvanized Pipe Replacement
We replace galvanized supply lines with copper or PEX — either as targeted section replacement at active failure points or as a full-house repipe project. We connect the new material to existing fittings using dielectric unions where code requires to prevent galvanic corrosion at copper-to-galvanized transitions.
PEX
PEX Pipe Repair & Extension
Cross-linked polyethylene (PEX) is the current standard for residential supply piping. Failures are uncommon but occur at crimp or clamp fittings that were improperly installed, at pipe runs exposed to UV degradation, or at locations where the pipe was kinked during installation. We repair using expansion fittings (for PEX-A) or crimp fittings with the correct ring size for the pipe diameter.
Burst Pipes
Burst & Freeze-Damaged Pipe Repair
We also inspect upstream of the burst for additional sections that froze but haven't yet failed — because a partially-thawed line sometimes shows multiple failure points only after pressure is restored.
Slab Leaks
Under-Slab Pipe Leak Repair
Supply line leaks under a concrete slab are identified by acoustic detection and confirmed by thermal imaging. Once located, we evaluate three repair options: direct-access repair (jackhammering to the pipe, repairing the section, and patching the slab); rerouting the line through the wall framing above slab to bypass the failed underground run; or epoxy pipe lining for older copper systems with systemic pinhole corrosion.
Full Repipe
Whole-House Repipe Service
A full repipe in Fulton typically completes in 2–3 days for a standard single-family home. You're without water for a portion of each day; we plan the schedule to minimize disruption to occupied rooms.
Here's how a Masters Plumbing Service pipe repair call plays out in Fulton, TX.
1
Call & Describe — We Shut the Water If Needed
Active leak? Our dispatcher walks you through shutting off the main supply valve while we drive to you. Describing what you see — water stain on a ceiling, drop in water pressure, wet flooring — helps us arrive with the right detection tools loaded.
2
Pressure Test & Acoustic / Thermal Detection
We pressurize the supply system and monitor for pressure drop to confirm an active leak. Then acoustic listening devices and the thermal camera locate the failure to within a small area — telling us which section of wall, floor, or slab to open.
3
Flat-Rate Quote & Minimal Access Opening
For slab leaks, we present repair, reroute, and lining options with pricing so you can make an informed choice before any concrete is cut.
4
Repair & Pressure Test — Then You're Done
Repair executes immediately on approval. After the repair, we repressurize and hold a pressure test to confirm the failure is fully resolved — not partially. The access opening is left clean for your drywall patch or left ready for your contractor.
Customer Reviews
Masters Plumbing Service Pipe Repair — How We Handle It
★★★★★
Water stain appeared on my kitchen ceiling from the bathroom above. I expected them to tear up the entire bathroom floor. Instead the tech ran a pressure test, found a 12% pressure drop over 10 minutes, then used the acoustic device and identified the leak at a failed sweat joint in the copper supply to the toilet — accessible through a 14-inch drywall cut in the ceiling below. Repair was maybe $280 including the detection. I'd been dreading a $2,000 floor demo.
— N. Bergman, Fulton
★★★★★
Had an under-slab leak diagnosed by Masters Plumbing Service with acoustic equipment. They found the leak at 6 feet from the wall — a single copper elbow that had developed a pinhole. Presented three options: direct slab access, reroute through the wall framing above, or copper lining. I chose the reroute — they ran a new PEX line through the crawl space and connected at both ends without touching the slab. Pressure tested, verified no remaining drop. No jackhammering at all.
— O. & R. Adeyemi, Fulton, TX
★★★★★
Pipe burst in a rental property at 2 AM — Masters Plumbing Service's emergency line answered immediately, talked my tenant through the main shutoff, and had a tech there in 45 minutes. Freeze crack in a PEX line in an exterior wall. Repair and insulation wrap done in under two hours. Detailed receipt for insurance documentation. Exactly what I needed as a landlord dealing with a crisis remotely.
— F. Okoro, Fulton, TX
Common Questions
Pipe Repair FAQ for Fulton, TX Homeowners
A slow pinhole leak inside a wall can run for months before surface damage appears. By the time you see a stain, the moisture intrusion is typically already significant. If your meter shows movement with everything off, call us — we can pressure-test and locate it before it becomes a major remediation project.
In some cases — particularly for older copper systems with multiple pinhole failures along a supply run — rerouting the line through accessible framing rather than repairing it in place is more practical and more permanent. We present both options when they're both viable.
Repair options include direct slab access (jackhammer to the pipe, repair, patch), rerouting the supply line above slab through framing, and for copper systems with multiple pinhole failures, epoxy pipe lining from inside the pipe without excavation. We use acoustic and thermal detection to locate the leak before recommending a repair approach.
Galvanized pipe corrodes from the interior outward — by the time one section fails, the rest of the pipe is in varying stages of the same process. A localized repair buys time, but another section typically fails within 1–3 years if the system is at end of life. The honest answer is: it depends on how far along the corrosion is and how many sections are already narrowed or showing surface rust.
We don't rush pressure testing at the end. That's the step that confirms the repair is actually complete, and it takes the time it takes.
Our pipe repair quote includes clean access cuts and leaving the opening ready for patching — with a clean, straight cut that accepts a standard drywall patch. We can typically patch the access opening as part of the job on request, though finish painting and texture matching are typically handled by the homeowner or a drywall contractor for best cosmetic results.
Service Area
Masters Plumbing Service Pipe Techs Serving Fulton, TX
Masters Plumbing Service dispatches pipe repair technicians throughout Fulton and the broader Fulton, TX service area. Same-day service is available on most calls. Emergency burst pipe response is available 24 hours a day.
Pipe Leaking in Fulton, TX? Don't Let It Run — Call Masters Plumbing Service
Active pipe leaks compound fast — mold growth can begin in 24–48 hours of sustained moisture. Masters Plumbing Service's pipe repair crew is in Fulton today, equipped with acoustic and thermal detection tools to find the failure precisely before anything is opened.
